AC Cable Size Chart: Wire Sizes, Ampacity & Applications

Choosing the correct cable for an alternating-current electrical system requires more than matching a wire to a voltage. AC cable size depends on conductor material, cross-sectional area, installation method, allowable ampacity, insulation temperature rating, ambient conditions, circuit length, and the connected load.

This AC cable size chart provides a practical overview of common conductor sizes, approximate ampacity ranges, voltage-drop considerations, and typical applications. Because ampacity varies according to installation conditions and electrical codes, the values below should be treated as general selection guidance rather than a substitute for code calculations or manufacturer data.


What Is an AC Cable?

An AC cable is a conductor or group of conductors used to carry alternating current between electrical equipment, distribution equipment, and loads. AC cables are used in residential, commercial, industrial, and utility applications.

Depending on the system, an AC cable may contain one or more insulated conductors along with a protective earth or grounding conductor.

Common AC cable applications include:

  • Residential branch circuits
  • Lighting circuits
  • Power outlets
  • Air-conditioning equipment
  • Pumps and motors
  • Industrial machinery
  • Distribution boards
  • Generators
  • HVAC systems
  • Solar AC connections
  • Commercial electrical installations

The correct cable size allows the circuit to carry its intended current without exceeding the conductor’s allowable operating temperature.


AC Cable Size Chart

Cable sizes are normally specified by conductor cross-sectional area in square millimeters (mm²) in many countries. The following table gives broad reference ranges for copper conductors under suitable installation conditions.

Cable Size Approximate Ampacity Range Typical Applications
1.0 mm² 10–15 A Lighting and light-duty circuits
1.5 mm² 14–20 A Lighting and small power circuits
2.5 mm² 18–27 A General-purpose outlets
4 mm² 25–36 A Larger branch circuits
6 mm² 32–46 A Higher-load circuits
10 mm² 45–63 A Feeders and larger equipment
16 mm² 60–85 A Distribution and heavy loads
25 mm² 80–110 A Larger feeders
35 mm² 100–135 A Industrial distribution
50 mm² 120–165 A High-current feeders
70 mm² 150–210 A Large distribution circuits
95 mm² 180–250 A High-current industrial feeders
120 mm² 210–285 A Large power distribution
150 mm² 240–325 A Heavy-duty distribution

These are general reference ranges, not universal ampacity ratings. The permitted current for a particular cable can change substantially with conductor material, insulation, number of loaded conductors, installation method, ambient temperature, grouping, and applicable electrical code.


How AC Cable Size Is Determined

The required cable size is primarily related to the current the circuit must carry.

For a single-phase AC circuit, a simplified relationship is:

Current = Power ÷ (Voltage × Power Factor)

For a three-phase AC system:

Current = Power ÷ (√3 × Voltage × Power Factor)

These equations can help estimate operating current, but cable selection requires additional considerations.

A proper selection should account for:

  • Load current
  • System voltage
  • Single-phase or three-phase supply
  • Power factor
  • Cable material
  • Insulation rating
  • Installation method
  • Ambient temperature
  • Number of loaded conductors
  • Voltage drop
  • Short-circuit requirements
  • Protective-device rating
  • Applicable electrical code

For motors and other equipment with significant starting current, the design must also consider starting conditions rather than only normal running current.


AC Cable Sizes in mm²

The mm² cable size describes the conductor’s cross-sectional area. It does not directly mean the overall outside diameter of the finished cable.

For example, a 6 mm² copper conductor has a nominal conductive cross-sectional area of 6 square millimeters. A complete cable containing insulation, sheath, multiple conductors, or shielding will have a considerably larger overall diameter.

Common AC conductor sizes include:

  • 1.0 mm²
  • 1.5 mm²
  • 2.5 mm²
  • 4 mm²
  • 6 mm²
  • 10 mm²
  • 16 mm²
  • 25 mm²
  • 35 mm²
  • 50 mm²
  • 70 mm²
  • 95 mm²
  • 120 mm²
  • 150 mm²

Larger cables may be used when current, voltage drop, fault conditions, or mechanical requirements demand them.


AC Cable Size and Ampacity

Ampacity is the amount of current a conductor can safely carry under specified conditions without exceeding its allowable temperature.

A cable’s ampacity is not determined by conductor size alone.

Factors That Affect Ampacity

Important factors include:

Conductor material: Copper and aluminum have different electrical properties.

Insulation: Different insulation systems have different temperature ratings.

Installation method: Cables installed in conduit, ducts, trays, walls, or free air can have different allowable currents.

Ambient temperature: Higher surrounding temperatures can reduce allowable ampacity.

Grouping: Closely grouped current-carrying conductors can require derating.

Number of loaded conductors: The number of simultaneously loaded conductors affects heat dissipation.

Cable construction: Single-core and multicore cables can have different thermal characteristics.

For this reason, an ampacity value from a generic chart should never automatically be treated as the final permitted current for an installation.


Copper vs Aluminum AC Cable

Copper and aluminum are both used for AC power distribution, but they have different characteristics.

Feature Copper Cable Aluminum Cable
Electrical conductivity Higher Lower
Conductor size for same current Generally smaller Generally larger
Weight Higher Lower
Typical use Branch circuits and many equipment connections Large feeders and distribution
Cost consideration Usually higher material cost Often lower material cost
Termination requirements Standard according to equipment Requires compatible rated connections

An aluminum conductor may require a larger cross-sectional area than copper for a comparable current-carrying requirement. Terminations must also be suitable for the conductor material and installation.


AC Cable Size for Single-Phase Systems

Single-phase AC systems are widely used for residential and smaller commercial loads.

The required conductor size depends on the operating current and installation conditions.

A simplified example illustrates the process. Suppose a 230 V load consumes 3,000 W and has a power factor of 1:

Current = 3,000 ÷ 230 ≈ 13 A

The calculated current does not automatically mean that any cable rated above 13 A is acceptable. Voltage drop, installation method, temperature, protective-device coordination, and local requirements must also be checked.

For inductive loads such as motors, the operating power factor and starting characteristics can further affect circuit design.


AC Cable Size for Three-Phase Systems

Three-phase AC power is commonly used for motors, commercial equipment, industrial machinery, and larger electrical loads.

For a balanced three-phase load, a commonly used relationship is:

I = P ÷ (√3 × V × PF)

Where:

  • I = line current
  • P = active power
  • V = line-to-line voltage
  • PF = power factor

For example, a three-phase motor’s cable size should be selected using its actual rated current and the relevant installation requirements rather than simply converting its power rating into a cable size.

Motor circuits may also require consideration of starting current, protective devices, motor-control equipment, and permitted voltage drop.

Also Read:


AC Cable Size and Voltage Drop

A cable can have sufficient thermal ampacity while still being too small for a long circuit because of voltage drop.

As current travels through a conductor, the conductor’s resistance causes some voltage to be lost. Longer cable runs generally produce greater voltage drop.

Voltage drop is affected by:

  • Cable length
  • Conductor resistance
  • Current
  • Conductor material
  • Cable size
  • Power factor
  • Circuit configuration
  • AC system type

If voltage drop is excessive, equipment may receive a lower voltage than intended. This can be particularly important for motors, compressors, long feeder circuits, and sensitive equipment.

Increasing conductor size can reduce resistance and therefore reduce voltage drop.

Also Read:


AC Cable Size by Typical Application

Different electrical loads have different current requirements and operating characteristics.

Application Common Cable Size Range Selection Considerations
Lighting 1.0–1.5 mm² Load current and circuit length
General outlets 2.5–4 mm² Circuit protection and installation method
Small appliances 1.5–2.5 mm² Appliance rating
Air conditioner 2.5–10 mm² Rated current and starting conditions
Water heater 4–10 mm² Power rating and circuit length
Small motors 2.5–6 mm² Motor current and starting
Large motors 6–35+ mm² Current, starting, voltage drop
Distribution feeder 10–150+ mm² Load, distance, and installation
Generator connection 6–150+ mm² Generator output and cable distance

These ranges are illustrative rather than universal. The equipment nameplate and applicable electrical requirements should take priority over a generic application table.


AC Cable Size Chart for Voltage and Current

The same cable size cannot be assigned to every AC voltage or current simply from a basic chart.

For example, a 2.5 mm² cable carrying a given current at a short distance may perform differently from the same conductor used on a long run. Likewise, a cable installed in free air can have different thermal conditions from one surrounded by insulation.

The following simplified relationship helps explain why larger conductors are often required as circuit length increases:

Voltage drop increases with current and conductor resistance.

Since conductor resistance decreases as conductor cross-sectional area increases, a larger cable can reduce voltage loss.

Also Read:


How to Select the Correct AC Cable Size

A practical cable-selection process can be organized into several steps.

Step 1: Determine the Load

Identify the equipment’s rated power, current, voltage, phase configuration, and power factor where applicable.

Step 2: Calculate or Confirm Circuit Current

Use the appropriate single-phase or three-phase relationship, or preferably use the equipment’s rated current when it is available.

Step 3: Select a Suitable Conductor

Compare the calculated load with the ampacity tables applicable to the actual installation method.

Step 4: Apply Derating Factors

Consider ambient temperature, conductor grouping, installation conditions, and other applicable correction factors.

Step 5: Check Voltage Drop

Calculate voltage drop for the actual cable length and load. Increase the conductor size if necessary.

Step 6: Coordinate Protection

The cable, circuit breaker, fuse, disconnect, and equipment should be appropriately coordinated according to the applicable requirements.

Step 7: Verify the Final Selection

Confirm the final cable specification using the applicable electrical code, manufacturer data, and project requirements.


Common AC Cable Size Mistakes

Incorrect cable selection can result from relying on conductor size alone.

Using Ampacity Without Checking Installation Conditions

A chart value may assume specific installation conditions. Changing the installation method can change the allowable current.

Ignoring Voltage Drop

Long circuits may require larger conductors even when the basic ampacity appears adequate.

Using the Same Size for Every Load

Lighting, heating, motors, drives, and other loads have different electrical characteristics.

Ignoring Conductor Material

Copper and aluminum cannot automatically be treated as interchangeable at the same cross-sectional area.

Choosing a Cable Before Calculating the Load

Cable size should follow the electrical requirements, not the other way around.

Forgetting Starting Current

Motors and compressors can draw substantially more current during startup than during normal operation.


AC Cable Size and Circuit Breaker Selection

The cable and protective device should be considered together.

A circuit breaker or fuse protects the circuit against conditions such as overload and short circuit, while the cable must be capable of safely carrying the expected load under its installation conditions.

The protective-device rating should not simply be chosen by matching it to a convenient cable size. The complete circuit design should account for:

  • Cable ampacity
  • Continuous and noncontinuous loads where applicable
  • Installation conditions
  • Fault-current requirements
  • Breaker characteristics
  • Equipment ratings
  • Local electrical regulations

A qualified electrical professional should verify final protection and conductor selection for installations where code compliance and safety are critical.


AC Cable Size for Motors

Motor circuits deserve special attention because motors can have high starting currents.

The selection may need to consider:

  • Motor full-load current
  • Starting method
  • Starting current
  • Motor efficiency
  • Power factor
  • Circuit length
  • Voltage drop
  • Ambient temperature
  • Installation method
  • Motor protection
  • Disconnecting requirements

For larger motors, selecting a cable solely from the motor’s horsepower rating can produce an incorrect result. The motor nameplate and applicable electrical requirements provide more useful information.


AC Cable Size and Cable Diameter

Cable size in mm² should not be confused with cable diameter.

For a round conductor, cross-sectional area is related to diameter by:

A = πd² ÷ 4

where A is cross-sectional area and d is conductor diameter.

However, measuring the outside diameter of an insulated cable does not directly tell you its conductor size because insulation and outer sheathing contribute to the overall diameter.

For accurate identification, use the cable marking, manufacturer specification, or an appropriate conductor measurement method.


Frequently Asked Questions

What is the most common AC cable size?

There is no single most common size for all AC systems. Sizes such as 1.5 mm², 2.5 mm², 4 mm², and 6 mm² are widely encountered in various low-voltage applications, but the appropriate size depends on the circuit.

How do I know what AC cable size I need?

Determine the load current, system voltage, phase configuration, cable length, installation method, conductor material, environmental conditions, voltage-drop requirements, and applicable electrical code.

Does a larger AC cable carry more current?

Generally, a larger conductor can carry more current under comparable conditions because it has greater cross-sectional area and can dissipate heat differently. The permitted ampacity must still be verified for the actual installation.

Is 2.5 mm² cable suitable for AC power?

It can be suitable for some AC power circuits, but its allowable current depends on the installation conditions and applicable requirements. Cable size should not be selected from cross-sectional area alone.

Which is better for AC, copper or aluminum cable?

Neither is universally better. Copper offers higher conductivity and can provide a smaller conductor for a comparable application, while aluminum can offer weight and material-cost advantages, particularly for larger conductors.

Does cable length affect AC cable size?

Yes. Longer circuits can experience greater voltage drop. A larger conductor may be required to maintain acceptable voltage at the load even when the basic thermal ampacity is adequate.


Conclusion

An AC cable size chart is a useful starting point for understanding conductor sizes, ampacity ranges, and typical applications, but it should not be used as the only basis for electrical cable selection.

The correct AC cable depends on load current, voltage, phase configuration, conductor material, installation method, temperature, cable grouping, circuit length, voltage drop, protection, and applicable electrical requirements. For a reliable installation, calculate the actual circuit requirements and verify the final cable against the relevant code and manufacturer specifications.