Medium Voltage Cable Size Chart: Complete Guide

Medium voltage cable sizing requires more than matching a conductor to a load current. The correct cable must satisfy ampacity, voltage rating, insulation level, installation method, voltage drop, short-circuit withstand, and environmental conditions.

This medium voltage cable size chart explains common conductor sizes and shows how ampacity changes with installation conditions. It also covers copper and aluminum conductors, voltage classes, insulation types, sizing factors, and common selection mistakes. Because ampacity depends heavily on cable construction and installation, the values in the example chart should be treated as a reference rather than a universal design table.


What Is a Medium Voltage Cable?

A medium voltage cable is a power cable designed to distribute electrical energy at voltages higher than typical low-voltage systems. Exact voltage classifications vary by electrical code and industry, but common medium voltage systems include 5 kV, 8 kV, 15 kV, 25 kV, 28 kV, 35 kV, and 46 kV classes.

Unlike ordinary low-voltage conductors, MV cables generally use a layered construction that controls the electrical field around the conductor. A typical shielded medium voltage cable may contain:

  • Conductor
  • Conductor shield
  • Primary insulation
  • Insulation shield
  • Metallic shield or concentric neutral
  • Jacket or armor

Common insulation materials include EPR (ethylene propylene rubber) and XLPE (cross-linked polyethylene). The cable construction, insulation temperature rating, shielding arrangement, and installation method all affect its allowable ampacity.


Medium Voltage Cable Size Chart

The conductor size is normally specified using AWG or kcmil in North American systems and metric cross-sectional area in many other regions. Larger conductors generally provide greater current-carrying capacity, but conductor size alone does not determine ampacity.

The following example uses a specific 15 kV copper MV cable construction with 133% insulation level and MV-105 rating. Its published ampacity values illustrate how the same conductor size can have different ratings in duct and air.

Conductor Size Approx. Area (mm²) Ampacity in Duct 90/105°C (A) Ampacity in Air 90/105°C (A)
2/0 AWG 67.4 220 / 235 245 / 275
4/0 AWG 107.2 285 / 305 325 / 360
500 kcmil 253.4 450 / 485 535 / 600
750 kcmil 380.0 545 / 585 670 / 745

The two ampacity figures represent the cable’s allowable ampacity under the applicable 90°C and 105°C conductor-temperature conditions for that particular cable construction and installation basis.

Important: This is an example manufacturer-specific chart, not a universal medium voltage ampacity table. Different insulation, conductor material, cable arrangement, ambient temperature, spacing, shielding, duct conditions, and installation configurations can produce substantially different results.


Common Medium Voltage Cable Sizes

Medium voltage cable sizes range from relatively small conductors for moderate loads to very large conductors for high-power feeders.

Common conductor sizes include:

  • 1 AWG
  • 1/0 AWG
  • 2/0 AWG
  • 3/0 AWG
  • 4/0 AWG
  • 250 kcmil
  • 350 kcmil
  • 500 kcmil
  • 600 kcmil
  • 750 kcmil
  • 1000 kcmil and larger

The most appropriate size depends on the required continuous current, installation conditions, voltage drop, fault level, and cable configuration.

A larger conductor is not automatically the best choice. Oversizing can increase material cost, cable diameter, pulling difficulty, termination requirements, and installation space.


AWG and kcmil in Medium Voltage Cables

Medium voltage conductors are commonly identified using American Wire Gauge (AWG) and circular mil or kcmil measurements.

AWG is commonly used for smaller conductor sizes. As the AWG number decreases, conductor area increases. Very large conductors are generally expressed in kcmil.

For example:

Conductor Size Approx. Cross-Sectional Area
1/0 AWG 53.5 mm²
2/0 AWG 67.4 mm²
3/0 AWG 85.0 mm²
4/0 AWG 107.2 mm²
250 kcmil 126.7 mm²
350 kcmil 177.3 mm²
500 kcmil 253.4 mm²
750 kcmil 380.0 mm²
1000 kcmil 506.7 mm²

These area conversions describe conductor cross-sectional area. They do not represent ampacity by themselves.


What Determines Medium Voltage Cable Ampacity?

Ampacity is the maximum continuous current a cable can carry under specified conditions without exceeding its permitted conductor temperature.

Several variables influence the final value.

Conductor Material

Copper and aluminum have different electrical characteristics.

Copper has higher electrical conductivity and is often selected where space, termination characteristics, or conductor size are important. Aluminum can provide a cost-effective alternative, particularly for larger power feeders.

However, aluminum conductor selection must account for its larger required cross-sectional area and appropriate terminals and connectors.

Insulation Temperature Rating

Cable insulation has a major influence on allowable operating temperature.

Common MV cable ratings include 90°C and 105°C continuous conductor-temperature ratings, depending on the cable design and applicable requirements.

A higher temperature rating does not automatically mean the cable can always carry more current. The complete installation must still satisfy the applicable ampacity method and limitations.

Installation Method

The same cable can have different ampacity values depending on whether it is installed:

  • In conduit
  • In underground duct
  • Directly buried
  • In a cable tray
  • In free air
  • In a thermal backfill system

Heat dissipation is one of the most important factors. A cable surrounded by materials that retain heat may have a lower allowable ampacity than an otherwise similar cable exposed to favorable cooling conditions.


How to Choose the Correct Medium Voltage Cable Size

Selecting an MV cable should be treated as an engineering process rather than a simple lookup.

1. Determine the System Voltage

Start with the system’s nominal voltage and required cable voltage class.

The cable’s insulation level must be appropriate for the system, including the grounding arrangement and any applicable insulation-level requirements.

2. Calculate the Design Load

Determine the expected continuous and applicable intermittent load current.

For a three-phase system, a simplified relationship between power, voltage, current, and power factor is:

I = P / (√3 × V × PF)

where:

  • I = current in amperes
  • P = three-phase power in watts
  • V = line-to-line voltage
  • PF = power factor

For motor loads, transformer feeders, and other specialized systems, starting current and operating characteristics may also need consideration.

3. Select a Preliminary Conductor Size

Choose a conductor size whose allowable ampacity meets the calculated load after applicable adjustment factors are considered.

Do not use a generic ampacity number simply because it appears beside a conductor size in a chart.

4. Check Voltage Drop

Voltage drop can become important on long medium voltage feeders, especially where motors or sensitive equipment are supplied.

Cable impedance, conductor size, power factor, circuit length, and operating current all influence voltage drop.

5. Check Short-Circuit Withstand

The conductor and metallic components must withstand the expected fault current for the specified clearing time.

Short-circuit performance can involve both the conductor and the cable shield, neutral, or grounding components.

6. Verify Physical Installation

Finally, check the physical requirements, including:

  • Cable outside diameter
  • Conduit or duct size
  • Minimum bending radius
  • Pulling tension
  • Sidewall pressure
  • Cable weight
  • Termination dimensions
  • Available installation space

A conductor that is electrically adequate may still be unsuitable if it cannot be installed safely within the available infrastructure.


Medium Voltage Cable Voltage Classes

Medium voltage cables are manufactured for different voltage classes. The correct rating depends on the electrical system rather than simply the operating voltage written on the equipment.

Common classes include:

Common Cable Class Typical Application Context
5 kV Industrial distribution and equipment feeders
8 kV Specialized medium voltage distribution
15 kV Industrial, utility, commercial, and distribution systems
25 kV Utility and industrial distribution
28 kV Selected distribution applications
35 kV Higher-voltage distribution systems
46 kV Upper medium-voltage distribution applications

The exact insulation level and cable construction should always be selected according to the system requirements and applicable standard.


Copper vs. Aluminum Medium Voltage Cable

Both conductor materials are widely used, but their characteristics differ.

Factor Copper Aluminum
Conductivity Higher Lower
Required conductor area for equivalent resistance Generally smaller Generally larger
Weight Higher for equivalent electrical performance Lower
Material cost Usually higher Usually lower
Large feeder applications Common Very common
Termination requirements Standard compatible terminations Requires compatible terminals and preparation

The decision should consider total installed cost rather than conductor purchase price alone.

For long feeders and large conductors, aluminum can offer significant weight and material advantages. Copper can be attractive where compact dimensions and higher conductivity are priorities.


Medium Voltage Cable Insulation Types

EPR Insulation

EPR is widely used in medium voltage power cables because of its electrical and thermal characteristics. EPR cables are commonly available in industrial and utility-oriented constructions.

XLPE Insulation

XLPE is another common MV cable insulation. It provides suitable electrical and thermal performance for many distribution applications and is available across a wide range of voltage classes.

The choice between EPR and XLPE should be based on the cable specification, environmental conditions, required temperature rating, installation requirements, and project standards.

Also Read:


Why Cable Installation Changes Ampacity

Ampacity is not simply a property of the conductor.

Heat produced by current must move away from the conductor. Installation conditions determine how effectively that heat can dissipate.

For example, relevant factors can include:

  • Ambient air temperature
  • Soil thermal resistivity
  • Burial depth
  • Duct arrangement
  • Number of loaded cables
  • Cable spacing
  • Conduit material
  • Cable grouping
  • Thermal backfill
  • Load factor
  • Conductor operating temperature

Multiple circuits installed close together can produce more heat and reduce the allowable current of individual cables.

This is why two projects using the same conductor size can legitimately have different ampacity results.


Medium Voltage Cable Shielding

Shielding is an important part of MV cable construction.

The conductor shield helps create a controlled electrical interface between the conductor and primary insulation. The insulation shield helps maintain a more uniform electric field around the insulation.

Depending on the cable design, the metallic shielding system may include:

  • Copper tape shield
  • Wire shield
  • Concentric neutral
  • Metallic screen
  • Other approved shielding arrangements

Shield design is also relevant to grounding, fault-current paths, induced voltages, and termination requirements.

The shield should therefore be treated as an integral part of the MV cable system rather than simply an additional protective layer.

Also Read:


Medium Voltage Cable Sizing for Long Runs

Long cable runs require more than an ampacity check.

A cable may have sufficient thermal ampacity while still producing unacceptable voltage drop or other electrical performance issues.

For longer circuits, evaluate:

  • Conductor resistance
  • AC impedance
  • Reactance
  • Operating power factor
  • Circuit length
  • Load current
  • Starting conditions
  • System voltage
  • Required receiving-end voltage

For large motors, voltage drop during starting can be particularly important because the motor can draw substantially more current than it does during normal operation.


Common Medium Voltage Cable Sizing Mistakes

Using Ampacity Without Checking Installation

A published ampacity is meaningful only when its installation conditions match the actual project.

Ignoring Voltage Drop

A cable can pass an ampacity calculation and still require a larger conductor because of voltage-drop requirements.

Choosing the Cable Only by Conductor Size

The conductor is only one part of an MV cable. Insulation level, shielding, jacket, temperature rating, and construction must also match the application.

Ignoring Short-Circuit Requirements

Fault-current withstand can affect conductor and shield selection even when normal operating current is relatively low.

Mixing Ampacity Tables

Ampacity values from different cable constructions should not be combined casually. A 15 kV cable with one insulation system and installation configuration may have a very different rating from another 15 kV cable.

Ignoring Manufacturer Data

The final cable should be selected from the actual manufacturer’s technical data and the applicable electrical standard rather than from a generic online chart alone.

Also Read:


Medium Voltage Cable Selection Checklist

Before specifying a cable, verify the following:

System voltage and voltage class

Continuous load current

Conductor material

Conductor size

Insulation type

Insulation level

Continuous temperature rating

Installation method

Ambient or soil conditions

Cable grouping

Voltage drop

Short-circuit withstand

Shielding and grounding

Cable diameter

Bending radius

Pulling tension

Termination compatibility

Applicable electrical standards

This checklist helps prevent the common mistake of treating cable sizing as a single ampacity calculation.


Frequently Asked Questions

What is the most common medium voltage cable size?

There is no single standard size used for every MV system. Sizes such as 2/0, 4/0, 350 kcmil, 500 kcmil, and 750 kcmil can be encountered, but the appropriate conductor depends on load, voltage, installation, and project requirements.

Does a larger cable always have higher ampacity?

Generally, a larger conductor can carry more current under comparable conditions. However, ampacity also depends on insulation, installation method, conductor temperature, cable arrangement, and environmental conditions.

Is copper better than aluminum for medium voltage cable?

Neither material is universally better. Copper offers higher conductivity and can achieve comparable electrical performance with a smaller conductor, while aluminum can reduce weight and material cost in many large feeder applications.

How do I calculate medium voltage cable ampacity?

Ampacity is normally determined using an applicable ampacity calculation method or table that accounts for the cable construction and installation. Factors such as conductor temperature, ambient conditions, spacing, grouping, and thermal environment must be considered.

Can I use a low-voltage cable size chart for an MV cable?

No. Medium voltage cables have different construction, insulation, shielding, and electrical requirements. An LV ampacity table should not be substituted for an appropriate MV cable sizing method.

What temperature rating should I use for an MV cable?

Use the temperature rating specified for the selected cable and permitted by the applicable installation requirements. Common MV constructions may have 90°C or 105°C continuous conductor ratings, but the complete cable system must be evaluated.


Final Takeaway

A medium voltage cable size chart is useful for understanding conductor sizes and comparing potential options, but it should not replace an engineering cable-sizing calculation. Ampacity depends on cable construction and installation conditions, while voltage rating, voltage drop, short-circuit withstand, shielding, and physical installation requirements also influence the final selection.

For a reliable design, start with the system voltage and load, select an appropriate conductor material and size, apply the correct installation-based ampacity method, then verify voltage drop, fault performance, and physical installation requirements. Always confirm the final selection against the manufacturer’s current technical data and applicable electrical standards.