Low Voltage Cable Size Chart: Sizes, Ampacity and Ratings

Choosing the correct cable is essential for electrical safety, reliable power delivery, and long-term system performance. A low voltage cable size chart helps users compare conductor sizes, understand ampacity, and identify suitable cable options for different electrical applications.

Low-voltage cables are commonly used for residential, commercial, industrial, control, lighting, distribution, and equipment connections. However, cable size cannot be selected from conductor diameter or voltage alone. The required size depends on current, installation conditions, voltage drop, conductor material, insulation temperature rating, cable construction, and applicable electrical requirements.

This guide explains common low-voltage cable sizes, how ampacity works, what voltage ratings mean, and how to select an appropriate cable for an installation.


What Is a Low Voltage Cable?

A low voltage cable is an insulated electrical cable designed to carry electrical power or signals at relatively low system voltages. The exact definition of low voltage varies by electrical code, standard, and application, so the term should not be treated as one universal voltage limit.

Low-voltage power cables may be used in building wiring, distribution systems, machinery, lighting circuits, control panels, and other electrical installations.

The conductor is commonly made from copper or aluminum. Copper offers high conductivity and is widely used in building and equipment wiring, while aluminum can be advantageous for larger conductors where weight and material cost are important.

A cable’s suitability depends on more than its conductor size. Important characteristics include:

  • Conductor material
  • Conductor cross-sectional area
  • Number of cores
  • Insulation material
  • Temperature rating
  • Voltage rating
  • Installation method
  • Ambient temperature
  • Number of loaded conductors
  • Cable grouping
  • Maximum allowable voltage drop
  • Environmental conditions

Low Voltage Cable Size Chart

Cable size is commonly expressed in square millimeters (mm²) for metric electrical systems. The conductor cross-sectional area generally increases as the cable’s current-carrying capability increases.

The following chart provides common metric conductor sizes and typical areas of use. It is a size-selection reference rather than a universal ampacity table, because the allowable current for a particular cable must be determined from its construction and installation conditions.

Cable Size (mm²) General Relative Capacity Common Applications
1.0 mm² Low Light-duty circuits and control applications
1.5 mm² Low Lighting and small circuits
2.5 mm² Moderate General-purpose power circuits
4 mm² Moderate Higher-load branch circuits
6 mm² Moderate–High Larger branch circuits and equipment
10 mm² High Feeders and higher-load equipment
16 mm² High Distribution and larger feeders
25 mm² High Main feeders and distribution
35 mm² High Larger distribution circuits
50 mm² Very High Industrial and high-load feeders
70 mm² Very High Large distribution systems
95 mm² Very High High-current feeders
120 mm² Very High Large power distribution
150 mm² Very High Heavy-duty distribution
185 mm² Very High Large industrial feeders
240 mm² Very High High-current distribution

These sizes should not be interpreted as having fixed ampacity values. A 25 mm² cable, for example, can have significantly different allowable current depending on conductor material, insulation, installation method, ambient temperature, number of loaded cables, and applicable standard.


What Does Cable Size Mean?

Cable size normally refers to the cross-sectional area of the conductor, rather than the outside diameter of the complete cable.

For example, a cable marked 6 mm² has a conductor with a nominal cross-sectional area of approximately 6 square millimeters. The actual outside diameter of the finished cable can be considerably larger because it includes insulation, sheathing, fillers, screens, armor, or other components.

Cable size affects several electrical characteristics:

  • Current-carrying capacity
  • Conductor resistance
  • Voltage drop
  • Heat generation
  • Physical flexibility
  • Cable weight
  • Installation requirements

A larger conductor generally has lower electrical resistance, but selecting the largest available cable is not automatically the correct solution. The cable must be properly matched to the circuit and installation.


Understanding Low Voltage Cable Ampacity

Ampacity is the maximum current a conductor can carry under specified conditions without exceeding its allowable temperature.

It is one of the most important considerations when selecting a low-voltage cable.

A cable carrying current produces heat because the conductor has electrical resistance. If the heat cannot be adequately dissipated, conductor temperature can rise beyond the permitted limit. Excessive temperature can damage insulation, reduce cable life, and create safety problems.

Ampacity therefore depends on conditions surrounding the cable, not just the conductor’s cross-sectional area.

Factors That Affect Ampacity

Important factors include:

  • Conductor material
  • Conductor size
  • Insulation temperature rating
  • Number of conductors carrying current
  • Ambient air or ground temperature
  • Cable installation method
  • Cable spacing
  • Conduit or trunking conditions
  • Direct burial conditions
  • Thermal insulation surrounding the cable
  • Cable grouping
  • Continuous-load requirements
  • Cable construction

For this reason, an ampacity number copied from one cable chart should not automatically be applied to another cable of the same nominal size.


Why There Is No Single Ampacity for Each Cable Size

It is tempting to create a chart showing one ampacity for every cable size, but that can be misleading.

Consider two cables that both contain a 10 mm² conductor. Their allowable current can differ because one may be installed in free air while another is enclosed in conduit. Their insulation systems may also have different temperature limits.

Similarly, several cables installed close together may dissipate heat differently from a single isolated cable.

Therefore, a proper low voltage cable size chart should be used together with the manufacturer’s data and the applicable electrical installation standard.

When exact ampacity is required, check:

  1. Cable manufacturer specifications
  2. Conductor material
  3. Insulation temperature rating
  4. Installation method
  5. Ambient conditions
  6. Cable grouping
  7. Applicable electrical code or standard
  8. Required correction or derating factors

Common Low Voltage Cable Sizes and Uses

Different conductor sizes are commonly selected for different levels of electrical load.

1.5 mm² Cable

A 1.5 mm² conductor is commonly associated with relatively small electrical circuits, particularly lighting and similar applications. Its suitability depends on the installation method and local electrical requirements.

It should not automatically be used simply because the circuit appears to have a small load. Protective-device selection and installation conditions must also be considered.

2.5 mm² Cable

2.5 mm² is a widely encountered conductor size for general-purpose electrical circuits. It can be used for various power applications when the circuit current, installation method, and voltage-drop requirements permit it.

4 mm² and 6 mm² Cable

These sizes provide larger conductor cross-sectional areas and may be selected for circuits with higher current demand, longer cable runs, or equipment requiring a larger conductor.

The correct choice still depends on the actual design conditions.

10 mm² and Larger Cables

Cables from 10 mm² upward are commonly encountered in feeders, distribution systems, larger equipment connections, and industrial electrical installations.

As cable sizes increase, installation considerations become increasingly important. Larger cables can be heavier, less flexible, and more difficult to terminate.


Low Voltage Cable Voltage Ratings

The voltage rating of a cable indicates the electrical voltage for which its insulation system is designed under specified conditions.

Voltage rating is different from ampacity.

A cable may have adequate current-carrying capacity but still be unsuitable if its voltage rating does not meet the system requirements.

Cable markings may specify voltage ratings in formats determined by the applicable cable standard. Always compare the cable’s marked rating with the electrical system and installation requirements.

Important considerations include:

  • System voltage
  • AC or DC application
  • Phase configuration
  • Insulation system
  • Applicable cable standard
  • Environmental conditions
  • Equipment requirements

Do not select a cable based only on conductor size.

Also Read:


Copper vs. Aluminum Low Voltage Cable

Copper and aluminum are two important conductor materials used in low-voltage cable systems.

Copper Cable

Copper has high electrical conductivity and is commonly used where compact conductors, flexibility, and reliable terminations are important.

Advantages can include:

  • High conductivity
  • Good mechanical properties
  • Common availability
  • Suitable for many building and equipment applications
  • Generally smaller conductor size for an equivalent electrical requirement compared with aluminum

Aluminum Cable

Aluminum is lighter than copper and is commonly used in larger conductors and power-distribution applications.

Potential advantages include:

  • Lower weight
  • Useful for large conductors
  • Common use in distribution systems

However, aluminum conductors require appropriate termination practices and compatible equipment. The manufacturer’s instructions and applicable installation requirements should always be followed.

Also Read:


How to Choose the Correct Low Voltage Cable Size

Selecting cable size should be treated as an electrical design process rather than simply matching a current number to a chart.

1. Determine the Load Current

Start by identifying the electrical load and determining the expected operating current.

For AC systems, the calculation depends on the type of circuit and load. Single-phase and three-phase systems use different relationships, and power factor may be relevant for certain loads.

2. Select the Conductor Material

Determine whether copper or aluminum is appropriate for the installation.

The same nominal conductor area does not necessarily provide identical electrical performance when different conductor materials are used.

3. Check Ampacity

Select a cable whose allowable current is adequate for the calculated load after applying relevant correction or derating factors.

Never assume the ampacity printed in a generic table applies to every installation.

4. Check Voltage Drop

A cable can have sufficient ampacity but still produce excessive voltage drop when the cable run is long.

Voltage drop depends on factors such as:

  • Conductor resistance
  • Cable length
  • Load current
  • Conductor size
  • Conductor material
  • AC system characteristics
  • Power factor where applicable

Increasing conductor size can reduce voltage drop, but the allowable limit should be determined from the applicable requirements.

5. Consider Installation Conditions

Determine how the cable will be installed.

Possible arrangements include:

  • In conduit
  • In trunking
  • In cable tray
  • Clipped or supported in air
  • Buried underground
  • Within equipment
  • In a cable duct
  • Bundled with other cables

The installation method can significantly affect heat dissipation and allowable current.

6. Check Environmental Conditions

Temperature, moisture, chemicals, sunlight, mechanical exposure, and other environmental factors may affect cable selection.

Outdoor or industrial installations may require cable construction specifically designed for the environment.

Also Read:


Cable Size and Voltage Drop

Voltage drop becomes particularly important on long cable runs.

When current flows through a conductor, some voltage is lost because of conductor impedance. The longer the cable and the higher the current, the more significant this effect can become.

A larger conductor generally has lower resistance and can therefore reduce voltage drop.

For example, if a small conductor is technically adequate for current capacity but the cable run is unusually long, a larger conductor may be required to satisfy the permitted voltage-drop limit.

This is why cable sizing should consider both ampacity and voltage drop.


Low Voltage Cable Size Selection Factors

Before purchasing or installing a cable, review the complete set of design requirements.

Selection Factor Why It Matters
Conductor Size Determines cross-sectional area and affects resistance
Conductor Material Copper and aluminum have different electrical characteristics
Ampacity Determines allowable current under specified conditions
Voltage Rating Must be suitable for the electrical system
Cable Length Influences voltage drop
Installation Method Affects heat dissipation and ampacity
Ambient Temperature Higher temperatures can reduce allowable current
Cable Grouping Multiple nearby cables can increase heating
Insulation Type Determines thermal and environmental performance
Environment Moisture, chemicals, sunlight, and mechanical exposure may matter
Protection Circuit protection must be coordinated with the cable
Termination Lugs, terminals, and equipment must accommodate the conductor

Common Low Voltage Cable Types

Low-voltage cables are available in many constructions designed for different applications.

Common categories include:

  • Single-core cables
  • Multicore cables
  • Flexible cables
  • Armored cables
  • Unarmored power cables
  • Control cables
  • Tray cables
  • Building wires
  • Underground cables
  • Outdoor-rated cables

The conductor size is only one part of cable selection. Two cables with identical conductor areas can have very different physical construction and intended uses.


Common Cable Sizing Mistakes

Several mistakes can result in an incorrectly sized cable.

Using Ampacity Alone

Ampacity is important, but it is not the only sizing requirement. Voltage drop, installation conditions, protection, and environmental factors can also influence the final selection.

Ignoring Derating

A cable may have a published ampacity under specific reference conditions. Grouping, temperature, and installation method can require the allowable current to be reduced.

Confusing Cable Diameter With Cable Size

The outside diameter of a finished cable is not the same thing as conductor cross-sectional area.

Choosing Cable by Appliance Rating Alone

The appliance’s current requirement does not provide enough information by itself. The complete circuit design must also be considered.

Ignoring Cable Length

Long cable runs can create voltage-drop problems even when the conductor appears adequate for current capacity.

Mixing Cable Standards

Cable ratings and sizing conventions vary between standards and regions. Data from one standard should not automatically be transferred to another.


Low Voltage Cable Size Chart: Quick Selection Guide

The following simplified chart can help organize the selection process, but it should not replace a code-compliant calculation.

Cable Size Typical Relative Use Main Consideration
1.0–1.5 mm² Small circuits Load and protection
2.5 mm² General-purpose circuits Ampacity and installation
4–6 mm² Higher-load branch circuits Current and voltage drop
10–16 mm² Feeders and larger equipment Installation and derating
25–50 mm² Distribution and industrial feeders Ampacity and voltage drop
70–120 mm² Large distribution Thermal conditions and termination
150–240 mm² High-current distribution Engineering calculation and installation method

These categories are intentionally general. There is no universal rule that assigns one exact load or ampacity to each cable size.


How to Read a Low Voltage Cable Marking

Cable markings provide important information about the product.

Depending on the cable type and standard, markings may identify:

  • Conductor material
  • Number of cores
  • Conductor cross-sectional area
  • Insulation type
  • Voltage rating
  • Temperature rating
  • Manufacturer
  • Applicable standard
  • Special construction characteristics

For example, a marking containing a conductor size such as 16 mm² identifies the nominal conductor cross-sectional area. It does not, by itself, tell you the exact permissible current in every installation.

Always interpret cable markings together with the manufacturer’s technical documentation.


Frequently Asked Questions

What is the most common low voltage cable size?

There is no single size that is correct for all low-voltage applications. Sizes such as 1.5 mm², 2.5 mm², 4 mm², 6 mm², and larger conductors are used for different circuit requirements.

Does a larger cable always carry more current?

Generally, a larger conductor can provide greater current-carrying capability under comparable conditions because it has a greater cross-sectional area. However, actual ampacity depends on installation conditions, insulation, conductor material, and applicable requirements.

How do I calculate low voltage cable size?

Begin with load current, then evaluate ampacity, voltage drop, installation method, ambient temperature, cable grouping, conductor material, insulation rating, and applicable electrical requirements.

Is copper better than aluminum for low voltage cables?

Neither is universally better. Copper provides high conductivity and is widely used in many applications, while aluminum offers lower weight and is commonly used for larger distribution conductors. The appropriate material depends on the system and installation requirements.

Does cable length affect cable size?

Yes. A longer cable run generally creates greater voltage drop. A larger conductor may therefore be necessary even when a smaller conductor has adequate current-carrying capacity.

Can I use a generic ampacity chart for any cable?

No. Generic charts should not be treated as universal. Ampacity depends on cable construction, insulation, installation conditions, ambient temperature, grouping, and the standard being used.

What is the difference between cable size and voltage rating?

Cable size primarily describes the conductor’s cross-sectional area, while voltage rating describes the electrical voltage the cable insulation system is designed to withstand under specified conditions. They are separate cable characteristics.


Final Thoughts

A low voltage cable size chart is useful for understanding common conductor sizes and organizing cable selection, but the correct cable cannot be chosen from conductor size alone. Ampacity, voltage drop, conductor material, insulation, installation method, temperature, grouping, protection, and voltage rating all need to be considered.

For a reliable selection, first determine the load current, then verify the cable’s allowable ampacity under the actual installation conditions. Check voltage drop for longer runs and confirm that the cable voltage rating, construction, terminations, and environmental characteristics suit the application.

Most importantly, use the manufacturer’s technical data and the electrical code or standard applicable to your installation when an exact cable size or ampacity is required.